LEWITT LCT 940
Condenser Microphone
EUR 1369.00
Incl. VAT, free shipping in Germany
Product # | 178960 |
Brand | LEWITT |
Category | Condenser Microphones | Brand Category | LEWITT - Condenser Mics |
Series | LEWITT LCT LEWITT LCT Promo |
Release date | December 2014 |
Availability | Will be ordered for you as quick as possible |
Description
The LCT 940 unifies the specific characteristics of a premium large diaphragm FET condenser microphone and a top-notch tube microphone.
With "Tube" you get warmth and musical harmonics, while "FET" gives you clear and nuanced sound. Blend tube and FET circuit at any ratio and find your ideal mix. The LCT 940 features a total of nine different polar patterns.
The LCT 940 combines a premium large-diaphragm FET condenser microphone and a top-notch tube microphone in a single housing.
There is a user interface on the remote control for a quick and accurate setup of pattern, pre-attenuation, and low-cut. Easily check or change the settings, even in complete darkness due to its illuminated user interface. The power supply unit is integrated.
By using the AMPLIFICATION knob, you can mix the two distinct microphone circuits, FET and tube circuit at any ratio to find your sweet spot.
This way you can dial in the ideal combination of warmth, punch, and clarity. Works brilliantly to adapt the LCT 940 to different voices.
A polar pattern affects how much room sound you end up recording. But switching your polar pattern not only changes the directivity, it also alters the frequency response, resulting in a different sound.
You can also control the proximity effect, and have it pronounced or reduced according to your application.
With "Tube" you get warmth and musical harmonics, while "FET" gives you clear and nuanced sound. Blend tube and FET circuit at any ratio and find your ideal mix. The LCT 940 features a total of nine different polar patterns.
The LCT 940 combines a premium large-diaphragm FET condenser microphone and a top-notch tube microphone in a single housing.
There is a user interface on the remote control for a quick and accurate setup of pattern, pre-attenuation, and low-cut. Easily check or change the settings, even in complete darkness due to its illuminated user interface. The power supply unit is integrated.
By using the AMPLIFICATION knob, you can mix the two distinct microphone circuits, FET and tube circuit at any ratio to find your sweet spot.
This way you can dial in the ideal combination of warmth, punch, and clarity. Works brilliantly to adapt the LCT 940 to different voices.
A polar pattern affects how much room sound you end up recording. But switching your polar pattern not only changes the directivity, it also alters the frequency response, resulting in a different sound.
You can also control the proximity effect, and have it pronounced or reduced according to your application.
Supplied items
Microphone, Shock mount, Windscreen, 11-pin audio cable, LCT 940 PSU, Protective case
Attributes
Product Details
| ||||||||||||||||
Dimension
|
Properties
Type: Condenser, externally polarized
Acoustical operating principle: Pressure gradient transducer
Transducer Ø: 25.4 mm, 1 in
Polar pattern: Omni, wide cardioid, cardioid, supercardioid, figure-8, four intermediate patterns
Frequency range: 20 ... 20,000 Hz
Sensitivity:
23 mV/Pa, -33 dBV/Pa (cardioid)
20 mV/Pa, -34 dBV/Pa (omni)
23 mV/Pa, -33 dBV/Pa (figure-8)
Equivalent noise level (FET):
8 dB (A), cardioid
9 dB (A), omni
8 dB (A), figure-8
Equivalent noise level (Tube):
12 dB (A), cardioid
13 dB (A), omni
12 dB (A), figure-8
Max. SPL for 0.5 % THD (FET): 143 dBSPL, 0 dB pre-attenuation
Max. SPL for 0.5% THD (Tube): 140 dBSPL, 0 dB pre-attenuation
Signal / noise ratio (FET): 86 dB (A)
Signal / noise ratio (Tube): 82 dB (A)
Dynamic range of FET mic. Amp.: 135 dB
Dynamic range of Tube mic. Amp.: 128 dB
Pre-attenuation pad:
0 dB
-6 dB
-12 dB
-18 dB
Low-cut filter:
linear
40 Hz (12 dB/oct)
150 Hz (6 dB/oct)
300 Hz (6 dB/oct)
Internal impedance: 200 Ω
Rated load impedance: 1,000 Ω
PSU - supply voltage:
230 V, 50 Hz
110 V, 60 Hz
Current consumption: 170 mA
Connector: Gold plated 11-pin XLR
Microphone dimensions: 192 x 60 x 46 mm, 7.5 x 2.4 x 1.8 in
PSU dimensions: 250 x 150 x 70 mm, 9.8 x 5.9 x 2.8 in
Microphone net weight: 662 g, 23.3 oz
PSU net weight: 1930 g, 68.1 oz
- Weight: 6.750kg
Acoustical operating principle: Pressure gradient transducer
Transducer Ø: 25.4 mm, 1 in
Polar pattern: Omni, wide cardioid, cardioid, supercardioid, figure-8, four intermediate patterns
Frequency range: 20 ... 20,000 Hz
Sensitivity:
23 mV/Pa, -33 dBV/Pa (cardioid)
20 mV/Pa, -34 dBV/Pa (omni)
23 mV/Pa, -33 dBV/Pa (figure-8)
Equivalent noise level (FET):
8 dB (A), cardioid
9 dB (A), omni
8 dB (A), figure-8
Equivalent noise level (Tube):
12 dB (A), cardioid
13 dB (A), omni
12 dB (A), figure-8
Max. SPL for 0.5 % THD (FET): 143 dBSPL, 0 dB pre-attenuation
Max. SPL for 0.5% THD (Tube): 140 dBSPL, 0 dB pre-attenuation
Signal / noise ratio (FET): 86 dB (A)
Signal / noise ratio (Tube): 82 dB (A)
Dynamic range of FET mic. Amp.: 135 dB
Dynamic range of Tube mic. Amp.: 128 dB
Pre-attenuation pad:
0 dB
-6 dB
-12 dB
-18 dB
Low-cut filter:
linear
40 Hz (12 dB/oct)
150 Hz (6 dB/oct)
300 Hz (6 dB/oct)
Internal impedance: 200 Ω
Rated load impedance: 1,000 Ω
PSU - supply voltage:
230 V, 50 Hz
110 V, 60 Hz
Current consumption: 170 mA
Connector: Gold plated 11-pin XLR
Microphone dimensions: 192 x 60 x 46 mm, 7.5 x 2.4 x 1.8 in
PSU dimensions: 250 x 150 x 70 mm, 9.8 x 5.9 x 2.8 in
Microphone net weight: 662 g, 23.3 oz
PSU net weight: 1930 g, 68.1 oz
- Weight: 6.750kg
Report incorrect data about this product